A collection of tips on how to be successful at plumbing makes the perfect starting point for a beginner. Below is just such a collection that will hopefully assist the eager novice into eventually becoming a pro when it comes to plumbing.

If you have pipes that make hammering and squeaking noises, you have one easy repair. Anchor any easily-accessible loose pipes. Pipes that are contained within the floors, walls and ceilings may need to be attended by a professional plumber.

Check the filters in your furnace, regularly. If these filters have not been cleaned or replaced recently, they may become clogged. This will affect how well your furnace is able to work, meaning that you may not have enough heat during the winter. Take this simple step, as soon as the weather starts to become cold.

Make sure you know where your home’s water shutoff is located. You never know when there might be an emergency involving a broken pipe or damaged connection that requires you to turn off the water right away. In addition, knowing where the shutoff is located is vital before you start any plumbing project, in case anything goes wrong.

If you have bad water pressure in the shower, the showerhead might be clogged. Take a plastic baggie, fill it with regular vinegar, and tie it to the showerhead so that the showerhead is covered. Leave it overnight. In the morning, take the baggie off and use a small toothbrush to scrub away any mineral deposits.

If you operate the disposal on your sink, run plenty of cool water. Blades will stay sharper with cold water, making disposal quicker. Hot water is not recommended because of what it does to greasy products.

Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing the damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out the damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove corrosion from inside the pipes with a wire brush. Apply flux to the replacement pipe and the remaining pipe. Slide the piece of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.

One easy way to save on energy and water is to install efficiency-oriented shower heads. Most households use a lot of hot water in the shower. By installing energy-efficient shower heads for a few extra dollars, you can save up to $100 or more a year per shower head in your house.

Your water heater works more during the fall and winter so make sure that you eliminate all sediment buildup around this piece of equipment. Flushing this device can lead to increased longevity so that you do not face plumbing problems during the winter. This precaution will save time, money and effort.

Cover pipes that are outside or in cool areas. Use heat tape to make sure that the pipes are completely covered and insulated. This will prevent frozen pipes in the winter, which can be an expensive problem. Check outdoor pipes for other problems such as leaks and cracks which are better to catch early.

During the warm seasons, you will see that there will be many bird nests forming in and around your plumbing vent pipes. It is essential to clear these out, as they can have a devastating effect on the quality of your plumbing and the flow of water in your home.

Check your faucets outside for dripping or leaking before winter arrives. If there are drips or leaks, then the repairs need to be make prior to any freezing temperatures. Regardless of the material of your particular pipes, whether it be copper, steel or plastic, water pressure from freezing water will cause pipes to crack. Even a very small crack can cause significant water damage or even can flood your entire home.

During the winter months, your water heater works the hardest. To keep it in optimum condition, flush it out before winter arrives. Flushing the system helps remove the sediment buildup, which causes internal corrosion of your water heater, shortens its lifespan, and reduces heating efficiency. Connect a hose to the faucet near the bottom of the tank and drain several gallons by directing the water into a nearby drain.

Well, hopefully the aforementioned collection of tips were enough to give you a great start on what to do and expect when it comes to maintaining your own plumbing. This collection was carefully constructed to be an aid in your arsenal so that you can begin to hone your plumbing skills into having a great plumbing system.