Now’s the time to expand your knowledge of plumbing. You’ve considered it previously, but never took the time to do it. Read the tips in this guide and you’ll be happy you did it if ever you experience any plumbing issues.

Before starting any plumbing project be sure to turn off the main water supply. Water damage can be one of the most expensive things to repair. To minimize damage turn the main water supply off as well as any shut off valves near where you are working. This will save a great deal of hardship later on.

Make sure you know where your home’s water shutoff is located. You never know when there might be an emergency involving a broken pipe or damaged connection that requires you to turn off the water right away. In addition, knowing where the shutoff is located is vital before you start any plumbing project, in case anything goes wrong.

If you have bad water pressure in the shower, the showerhead might be clogged. Take a plastic baggie, fill it with regular vinegar, and tie it to the showerhead so that the showerhead is covered. Leave it overnight. In the morning, take the baggie off and use a small toothbrush to scrub away any mineral deposits.

Check your gas water heater periodically to make sure the pilot flame is lit. The correct color for this flame should be blue. The tip of the flame should be yellow. If you find that you are only seeing a yellow flame, you may need to call a professional for safety reasons.

Making sure you know all of your problems so you can have them fixed by one plumber visit is very beneficial. Having them all fixed in one visit takes a lot of money off of your bill because you don’t have to pay for the visit multiple times so make sure you make a list first.

Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing the damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out the damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove corrosion from inside the pipes with a wire brush. Apply flux to the replacement pipe and the remaining pipe. Slide the piece of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.

Some people have problems with their plumbing system in that the pipes sweat and drip condensation. You do not have to hire a plumber to take care of this nuisance. You can purchase self-adhesive drip tape from your local hardware store. This drip tape will insulate your “sweating” pipes which are dripping with moisture built up from condensation. To make sure the tape sticks firmly, dry the pipe thoroughly before applying the tape.

Make sure you get a good recommendation or check the references before you hire a plumber. With good recommendations, it will assure that you are hiring an experienced plumber. If the experienced plumber is professional, he will have a fully stocked truck and be able to complete most small jobs in one visit.

Don’t start any do-it-yourself plumbing project without having a plan in place. You need to know beforehand exactly what you are getting yourself into. Know what kind of space you are working with and what lines are which. Getting a clear picture early on will make your plumbing project go a lot smoother!

Find out the plumbing codes in your local area before starting any project. Plumbing codes can vary wildly from area to area and you don’t want to run afoul of the codes. Visit your local building department to find out information or hire a plumber for a day to help you go over your plans and provide advice.

To avoid freezing pipes in the winter, make sure to insulate any exposed pipes in you basement before winter comes. Pay extra attention to pipes near the outside walls. If you have had a problem with any particular pipe freezing in the past, apply some heat tape to insulate those pipes.

In the winter months, if you live somewhere where temperatures fall below freezing, leave your faucets on a little bit to let a thin stream of water through. This will help prevent the pipes from freezing, which could be a major problem for you and all the pipes in your home.

Finally, it’s very valuable to know about your plumbing system. You will be able to save yourself a bunch of money, plus many of your friends and family members will come to you for advice. The information above was delivered in a straightforward manner, so you should have no trouble understanding and implementing any of the above techniques.