If you’ve ever hired a professional plumber for something simple, you know how expensive and annoying the experience can be. If you’d like to save a little cash by learning how to solve your own plumbing problems, read on. This article will give you the knowledge you need for your own plumbing repair.

On very cold winter nights, allow your faucets to trickle slightly, especially if your pipes are located in a crawlspace. The running water prevents the pipes from freezing as quickly as they would otherwise. You can catch the water and use it for other household needs to prevent wasting it.

You do not give the plumber all the money until he is finished with his work. You might have to give them a deposit, but do not give them the entire sum of money until you are sure they have done a good job. Knowing the job was completed in a timely and high-quality manner is essential before paying for a plumber.

To winterize a house that will sit unused during the winter months, you must completely drain all of the pipes. After turning off the main water supply, let all of the water drain from the faucets, toilets, and water heater (turn off the gas). Add a quart of antifreeze to sinks and the tub to prevent water from freezing in the drain trap.

If your toilet is slow to flush, add some white vinegar to the overflow tube. White vinegar helps the water from your tank to flow quickly, which will make the toilet flush faster. It is recommended that you use about a quart of the vinegar and let it stay there for at least an hour before flushing.

Check your gas water heater periodically to make sure the pilot flame is lit. The correct color for this flame should be blue. The tip of the flame should be yellow. If you find that you are only seeing a yellow flame, you may need to call a professional for safety reasons.

Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing the damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out the damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove corrosion from inside the pipes with a wire brush. Apply flux to the replacement pipe and the remaining pipe. Slide the piece of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.

Watch how your toilets are flushing. If you have to jiggle the handle or if it takes too long, you might have to repair some toilet parts. Replacing these parts early may help you to save on your water bills and will save you from more expensive repairs at a later date.

Some people have problems with their plumbing system in that the pipes sweat and drip condensation. You do not have to hire a plumber to take care of this nuisance. You can purchase self-adhesive drip tape from your local hardware store. This drip tape will insulate your “sweating” pipes which are dripping with moisture built up from condensation. To make sure the tape sticks firmly, dry the pipe thoroughly before applying the tape.

Drain the sediment from the bottom of your hot water heater twice a year to keep the hot water heater working at its optimal levels. Simply open the drain valve and allow the water to run out into a bucket until the water runs clear. Then close the drain valve.

DIY plumbing jobs will require that you understand how to solder copper for the lines for the water supply. You can practice this skill so that you will be able to run your lines without worrying about it leaking. Search online for video tutorials that can help you get a handle on how to go about soldering.

If you are using PEX tubing for the supply lines in your home, make sure you get the right tools for the job. PEX tubing requires a completely different tool type than regular lines. PEX has a lot of benefits though, so don’t let the different requirements throw you off.

There are simple ways to check your toilet for leaks that can ultimately lead to great cost savings in the long run. The easiest way to do this is to pour a small amount of food dye into the holding tank of your toilet overnight. In the morning, if you have any color in the basin then you know you have a leak that needs some attention.

As you can see, hiring a professional plumber is usually an unnecessary and expensive thing to do, compared to fixing the problem yourself. Next time your plumbing needs repair, try pulling up this article and trying to solve it yourself. You may be surprised how easy it is to do!