There may come a time when you have issues with your plumbing, whether it’s a clogged sink or plugged up toilet. Check out the tips and suggestions in the article below that will show you easy things you can do on your own to solve these issues, and save a call to a plumber.

To keep your pipes from getting frozen, always maintain a temperature in the house above freezing and make sure all pipes exposed to outside elements are insulated properly. Pipes will freeze if they are exposed to temperatures below freezing. It could take some time in order for the pipes to thaw out so that you can have running water. The worst case scenario is a busted pipe and a costly repair.

Don’t pay a plumber until the job is completed. A plumber may require some money upfront, but it’s wise to wait until the job is completely done before giving him the entire payment. Many things can happen between the stop and end of a job, so to be safe wait until you are satisfied with the completed work before paying.

Be careful about using liquid clog cleaners. These liquids can contain chemicals that are extremely bad for your pipes. Instead, use a snake or a plunger to dislodge any clogs you might encounter. Be sure to try these things before giving up and calling a plumber, who will probably re-perform those same acts.

Group all of your plumbing repairs before scheduling a plumber to come out. Check all of your fixtures and faucets. If anything is dripping, running or clogged, make a list for the plumber. That way, when the plumber comes, they can do all of the jobs in one visit. This will cut down on charges.

Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing the damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out the damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove corrosion from inside the pipes with a wire brush. Apply flux to the replacement pipe and the remaining pipe. Slide the piece of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.

Set the temperature on your hot water heater to a temperature that does not exceed 120 degrees. This helps to save energy and prevents the water from becoming too hot and potentially scalding someone in your household. Older models that do not have a temperature setting should be set on Medium.

Your water heater works more during the fall and winter so make sure that you eliminate all sediment buildup around this piece of equipment. Flushing this device can lead to increased longevity so that you do not face plumbing problems during the winter. This precaution will save time, money and effort.

Before you can fix a toilet that does not flush properly, it is important that you find out what is causing the problem. Depending on what the problem is, you may be able to fix it yourself. However, more complicated toilet flushing problems may require the services of a plumber.

If you have problems with a slow drain, there are easier things you can do other than removing the pipes to clean it. There are certain tools made just for this purpose that you insert into the drain to loosen the clog so it washes away or grab it and remove it completely.

If you are trying to decide on the material to use for your hose, stick with stainless steel. Stainless steel has a very solid construction and stays durable for many years, eliminating the need for replacement. Also, this material is less prone to bursting, which can yield severe plumbing issues.

Garbage disposals are a common cause of plumbing problems, which is an easy problem to solve. Don’t just put everything down the disposal or treat it like a second trash can. Use the disposal things that would be difficult to dispose of normally. Putting all leftover food down the sink is a good way to produce clogs.

If you have an odor coming from one or more fixtures in your house, it is likely this has to do with the water in water traps. Each fixture has a water trap that is sealed off to prevent odors. If the water evaporates, the odors can surface. Therefore, try adding water to the traps.

As was shown in the above article, there are many plumbing issues that can be handled by someone other than a plumber. Once you take the time to read how to do it, you will be amazed at the things you will be doing without the expense of an expert.